|ROUTE(8)||FreeBSD System Manager's Manual||ROUTE(8)|
NAMEroute — manually manipulate the routing tables
|route||[ -dnqtv] command [ [ modifiers] args]|
DESCRIPTIONThe route utility is used to manually manipulate the network routing tables. It normally is not needed, as a system routing table management daemon, such as routed(8), should tend to this task.
The route utility supports a limited number of general options, but a rich command language, enabling the user to specify any arbitrary request that could be delivered via the programmatic interface discussed in route(4).
The following options are available:
- Specify inet address family as family hint for subcommands.
- Specify inet address family as family hint for subcommands.
- Run in debug-only mode, i.e., do not actually modify the routing table.
- Bypass attempts to print host and network names symbolically when reporting actions. (The process of translating between symbolic names and numerical equivalents can be quite time consuming, and may require correct operation of the network; thus it may be expedient to forget this, especially when attempting to repair networking operations).
- Run in test-only mode. /dev/null is used instead of a socket.
- (verbose) Print additional details.
- Suppress all output from the add, change, delete, and flush commands.
The route utility provides the following commands:
- Add a route.
- Remove all routes.
- Delete a specific route.
- Another name for the delete command.
- Change aspects of a route (such as its gateway).
- Lookup and display the route for a destination.
- Continuously report any changes to the routing information base, routing lookup misses, or suspected network partitionings.
- Another name for the get command.
The monitor command has the syntax:
The flush command has the syntax:
If the flush command is specified, route will ``flush'' the routing tables of all gateway entries. When the address family may is specified by any of the -osi, -xns, -atalk, -inet6, or -inet modifiers, only routes having destinations with addresses in the delineated family will be deleted. Additionally, -4 or -6 can be used as aliases for -inet and -inet6 modifiers. When a -fib option is specified, the operation will be applied to the specified FIB (routing table).
The other commands have the following syntax:
where destination is the destination host or network, gateway is the next-hop intermediary via which packets should be routed. Routes to a particular host may be distinguished from those to a network by interpreting the Internet address specified as the destination argument. The optional modifiers -net and -host force the destination to be interpreted as a network or a host, respectively. Otherwise, if the destination has a “local address part” of INADDR_ANY (
0.0.0.0), or if the destination is the symbolic name of a network, then the route is assumed to be to a network; otherwise, it is presumed to be a route to a host. Optionally, the destination could also be specified in the net/ bits format.
128.32 is interpreted as -host
128.32.130 is interpreted as -host
128.32 is interpreted as
128.32.130 is interpreted as
192.168.64/20 is interpreted as -net
A destination of default is a synonym for the default route. For
IPv4 it is -net -inet
0.0.0.0, and for
IPv6 it is -net -inet6
If the destination is directly reachable via an interface requiring no intermediary system to act as a gateway, the -interface modifier should be specified; the gateway given is the address of this host on the common network, indicating the interface to be used for transmission. Alternately, if the interface is point to point the name of the interface itself may be given, in which case the route remains valid even if the local or remote addresses change.
The optional modifiers -xns, -osi, -atalk, and -link specify that all subsequent addresses are in the XNS, OSI, or AppleTalk address families, or are specified as link-level addresses, and the names must be numeric specifications rather than symbolic names.
The optional -netmask modifier is intended to achieve the effect of an OSI ESIS redirect with the netmask option, or to manually add subnet routes with netmasks different from that of the implied network interface (as would otherwise be communicated using the OSPF or ISIS routing protocols). One specifies an additional ensuing address parameter (to be interpreted as a network mask). The implicit network mask generated in the AF_INET case can be overridden by making sure this option follows the destination parameter.
For AF_INET6, the -prefixlen qualifier is available instead of the -mask qualifier because non-continuous masks are not allowed in IPv6. For example, -prefixlen
32 specifies network mask of
ffff:ffff:0000:0000:0000:0000:0000:0000 to be used. The default value of prefixlen is 64 to get along with the aggregatable address. But 0 is assumed if default is specified. Note that the qualifier works only for AF_INET6 address family.
Routes have associated flags which influence operation of the protocols when sending to destinations matched by the routes. These flags may be set (or sometimes cleared) by indicating the following corresponding modifiers:
-xresolve RTF_XRESOLVE - emit mesg on use (for external lookup) -iface ~RTF_GATEWAY - destination is directly reachable -static RTF_STATIC - manually added route -nostatic ~RTF_STATIC - pretend route added by kernel or daemon -reject RTF_REJECT - emit an ICMP unreachable when matched -blackhole RTF_BLACKHOLE - silently discard pkts (during updates) -proto1 RTF_PROTO1 - set protocol specific routing flag #1 -proto2 RTF_PROTO2 - set protocol specific routing flag #2 -proto3 RTF_PROTO3 - set protocol specific routing flag #3
The optional modifiers -rtt, -rttvar, -sendpipe, -recvpipe, -mtu, -hopcount, -expire, and -ssthresh provide initial values to quantities maintained in the routing entry by transport level protocols, such as TCP or TP4. These may be individually locked by preceding each such modifier to be locked by the -lock meta-modifier, or one can specify that all ensuing metrics may be locked by the -lockrest meta-modifier.
Note that -expire accepts expiration time of the route as the number of seconds since the Epoch (see time(3)). When the first character of the number is “+” or “-”, it is interpreted as a value relative to the current time.
The optional modifier -fib number specifies that the command will be applied to a non-default FIB. The number must be smaller than the net.fibs sysctl(8) MIB. When this modifier is not specified, or a negative number is specified, the default FIB shown in the net.my_fibnum sysctl(8) MIB will be used.
The number allows multiple FIBs by a comma-separeted list and/or range specification. The “ -fib
2,4,6” means the FIB number 2, 4, and 6. The “ -fib
1,3-5,6” means the 1, 3, 4, 5, and 6.
In a change or add command where the destination and gateway are not sufficient to specify the route (as in the ISO case where several interfaces may have the same address), the -ifp or -ifa modifiers may be used to determine the interface or interface address.
All symbolic names specified for a destination or gateway are looked up first as a host name using gethostbyname(3). If this lookup fails, getnetbyname(3) is then used to interpret the name as that of a network.
The route utility uses a routing socket and the new message types RTM_ADD, RTM_DELETE, RTM_GET, and RTM_CHANGE. As such, only the super-user may modify the routing tables.
EXIT STATUSThe route utility exits 0 on success, and >0 if an error occurs.
EXAMPLESAdd a default route to the network routing table. This will send all packets for destinations not available in the routing table to the default gateway at 192.168.1.1:
route add -net 0.0.0.0/0 192.168.1.1
A shorter version of adding a default route can also be written as:
route add default 192.168.1.1
Add a static route to the 172.16.10.0/24 network via the 172.16.1.1 gateway:
route add -net 172.16.10.0/24 172.16.1.1
Change the gateway of an already established static route in the routing table:
route change -net 172.16.10.0/24 172.16.1.2
Display the route for a destination network:
route show 172.16.10.0
Delete a static route from the routing table:
route delete -net 172.16.10.0/24 172.16.1.2
Remove all routes from the routing table:
- add [host | network ] %s: gateway %s flags %x
- The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl(2) call. If the gateway address used was not the primary address of the gateway (the first one returned by gethostbyname(3)), the gateway address is printed numerically as well as symbolically.
- delete [ host | network ] %s: gateway %s flags %x
- As above, but when deleting an entry.
- %s %s done
- When the flush command is specified, each routing table entry deleted is indicated with a message of this form.
- Network is unreachable
- An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
- not in table
- A delete operation was attempted for an entry which was not present in the tables.
- routing table overflow
- An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
- gateway uses the same route
- A change operation resulted in a route whose gateway uses the same route as the one being changed. The next-hop gateway should be reachable through a different route.
HISTORYThe route utility appeared in 4.2BSD.
BUGSThe first paragraph may have slightly exaggerated routed(8)'s abilities.
Currently, routes with the RTF_BLACKHOLE flag set need to have the gateway set to an instance of the lo(4) driver, using the -iface option, for the flag to have any effect; unless IP fast forwarding is enabled, in which case the meaning of the flag will always be honored.
|May 8, 2014||FreeBSD|