EN JA
USB_QUIRK(4)
USB_QUIRK(4) FreeBSD Kernel Interfaces Manual USB_QUIRK(4)

NAME

usb_quirkUSB quirks module

SYNOPSIS

To compile this module into the kernel, place the following line in your kernel configuration file:

device usb

Alternatively, to load the module at boot time, place the following line in loader.conf(5):

usb_quirk_load="YES"

DESCRIPTION

The usb_quirk module provides support for dynamically adding and removing quirks for USB devices with usbconfig(8).

General quirks:

UQ_AUDIO_SWAP_LR
swap left and right channels
UQ_AU_INP_ASYNC
input is async despite claim of adaptive
UQ_AU_NO_FRAC
do not adjust for fractional samples
UQ_AU_NO_XU
audio device has broken extension unit
UQ_BAD_ADC
bad audio spec version number
UQ_BAD_AUDIO
device claims audio class, but is not
UQ_BROKEN_BIDIR
printer has broken bidir mode
UQ_BUS_POWERED
device is bus powered, despite claim
UQ_HID_IGNORE
device should be ignored by hid class
UQ_KBD_IGNORE
device should be ignored by kbd class
UQ_KBD_BOOTPROTO
device should set the boot protocol
UQ_UMS_IGNORE
device should be ignored by ums class
UQ_MS_BAD_CLASS
does not identify properly
UQ_MS_LEADING_BYTE
mouse sends an unknown leading byte
UQ_MS_REVZ
mouse has Z-axis reversed
UQ_NO_STRINGS
string descriptors are broken
UQ_POWER_CLAIM
hub lies about power status
UQ_SPUR_BUT_UP
spurious mouse button up events
UQ_SWAP_UNICODE
has some Unicode strings swapped
UQ_CFG_INDEX_1
select configuration index 1 by default
UQ_CFG_INDEX_2
select configuration index 2 by default
UQ_CFG_INDEX_3
select configuration index 3 by default
UQ_CFG_INDEX_4
select configuration index 4 by default
UQ_CFG_INDEX_0
select configuration index 0 by default
UQ_ASSUME_CM_OVER_DATA
assume cm over data feature

USB Mass Storage quirks:

UQ_MSC_NO_TEST_UNIT_READY
send start/stop instead of TUR
UQ_MSC_NO_RS_CLEAR_UA
does not reset Unit Att.
UQ_MSC_NO_START_STOP
does not support start/stop
UQ_MSC_NO_GETMAXLUN
does not support get max LUN
UQ_MSC_NO_INQUIRY
fake generic inq response
UQ_MSC_NO_INQUIRY_EVPD
does not support inq EVPD
UQ_MSC_NO_SYNC_CACHE
does not support sync cache
UQ_MSC_SHUTTLE_INIT
requires Shuttle init sequence
UQ_MSC_ALT_IFACE_1
switch to alternate interface 1
UQ_MSC_FLOPPY_SPEED
does floppy speeds (20kb/s)
UQ_MSC_IGNORE_RESIDUE
gets residue wrong
UQ_MSC_WRONG_CSWSIG
uses wrong CSW signature
UQ_MSC_RBC_PAD_TO_12
pad RBC requests to 12 bytes
UQ_MSC_READ_CAP_OFFBY1
reports sector count, not max sec.
UQ_MSC_FORCE_SHORT_INQ
does not support full inq.
UQ_MSC_FORCE_WIRE_BBB
force BBB wire protocol
UQ_MSC_FORCE_WIRE_CBI
force CBI wire protocol
UQ_MSC_FORCE_WIRE_CBI_I
force CBI with int. wire protocol
UQ_MSC_FORCE_PROTO_SCSI
force SCSI command protocol
UQ_MSC_FORCE_PROTO_ATAPI
force ATAPI command protocol
UQ_MSC_FORCE_PROTO_UFI
force UFI command protocol
UQ_MSC_FORCE_PROTO_RBC
force RBC command protocol

3G Datacard (u3g) quirks:

UQ_MSC_EJECT_HUAWEI
ejects after Huawei USB command
UQ_MSC_EJECT_SIERRA
ejects after Sierra USB command
UQ_MSC_EJECT_SCSIEJECT
ejects after SCSI eject command 0x1b0000000200
UQ_MSC_EJECT_REZERO
ejects after SCSI rezero command 0x010000000000
UQ_MSC_EJECT_ZTESTOR
ejects after ZTE SCSI command 0x850101011801010101010000
UQ_MSC_EJECT_CMOTECH
ejects after C-motech SCSI command 0xff52444556434847
UQ_MSC_EJECT_WAIT
wait for the device to eject
UQ_MSC_EJECT_SAEL_M460
ejects after Sael USB commands
UQ_MSC_EJECT_HUAWEISCSI
ejects after Huawei SCSI command 0x11060000000000000000000000000000
UQ_MSC_EJECT_TCT
ejects after TCT SCSI command 0x06f504025270

See /sys/dev/usb/quirk/usb_quirk.h for the complete list of supported quirks.

EXAMPLES

After attaching a u3g device which appears as a USB device on ugen0.3:

usbconfig -d ugen0.3 add_quirk UQ_MSC_EJECT_WAIT

SEE ALSO

usbconfig(8)

HISTORY

The usb_quirk module appeared in FreeBSD 8.0, and was written by Hans Petter Selasky <hselasky@FreeBSD.org>. This manual page was written by Nick Hibma <n_hibma@FreeBSD.org>.
April 21, 2013 FreeBSD