KEYBOARD(4) FreeBSD Kernel Interfaces Manual KEYBOARD(4)


keyboardpc keyboard interface


The PC keyboard is used as the console character input device. The keyboard is owned by the current virtual console. To switch between the virtual consoles use the sequence ALT+Fn, which means hold down ALT and press one of the function keys. The virtual console with the same number as the function key is then selected as the current virtual console and given exclusive use of the keyboard and display.

The console allows entering values that are not physically present on the keyboard via a special keysequence. To use this facility press and hold down ALT, then enter a decimal number from 0-255 via the numerical keypad, then release ALT. The entered value is then used as the ASCII value for one character. This way it is possible to enter any ASCII value, not present on the keyboard. The console driver also includes a history function. It is activated by pressing the scroll-lock key. This holds the display, and enables the cursor arrows for scrolling up and down through the last scrolled out lines.

The keyboard is configurable to suit the individual user and the different national layout.

The keys on the keyboard can have any of the following functions:

Normal key
Enter the ASCII value associated with the key.
Function key
Enter a string of ASCII values.
Switch Key
Switch virtual console.
Modifier Key
Change the meaning of another key.

The keyboard is seen as a number of keys numbered from 1 to n. This number is often referred to as the "scancode" for a given key. The number of the key is transmitted as an 8 bit char with bit 7 as 0 when a key is pressed, and the number with bit 7 as 1 when released. This makes it possible to make the mapping of the keys fully configurable.

The meaning of every key is programmable via the PIO_KEYMAP ioctl call, that takes a structure keymap_t as argument. The layout of this structure is as follows:

  struct keymap { 
   u_short n_keys; 
   struct key_t { 
    u_char map[NUM_STATES]; 
    u_char spcl; 
    u_char flgs; 
   } key[NUM_KEYS]; 

The field n_keys tells the system how many keydefinitions (scancodes) follows. Each scancode is then specified in the key_t substructure.

Each scancode can be translated to any of 8 different values, depending on the shift, control, and alt state. These eight possibilities are represented by the map array, as shown below:

 scan                          cntrl          alt    alt   cntrl 
 code     base   shift  cntrl  shift   alt   shift  cntrl  shift 
 map[n]      0       1      2      3     4       5      6      7 
 ----     ------------------------------------------------------ 
 0x1E      'a'     'A'   0x01   0x01    'a'    'A'   0x01   0x01

This is the default mapping for the key labelled 'A' which normally has scancode 0x1E. The eight states are as shown, giving the 'A' key its normal behavior. The spcl field is used to give the key "special" treatment, and is interpreted as follows. Each bit corresponds to one of the states above. If the bit is 0 the key emits the number defined in the corresponding map[] entry. If the bit is 1 the key is "special". This means it does not emit anything; instead it changes the "state". That means it is a shift, control, alt, lock, switch-screen, function-key or no-op key. The bitmap is backwards i.e., 7 for base, 6 for shift etc.

The flgs field defines if the key should react on caps-lock (1), num-lock (2), both (3) or ignore both (0).

The kbdcontrol(1) utility is used to load such a description into/outof the kernel at runtime. This makes it possible to change the key assignments at runtime, or more important to get (GIO_KEYMAP ioctl) the exact key meanings from the kernel (e.g. used by the X server).

The function keys can be programmed using the SETFKEY ioctl call.

This ioctl takes an argument of the type fkeyarg_t:

  struct fkeyarg { 
   u_short keynum; 
   char keydef[MAXFK]; 
   char flen; 

The field keynum defines which function key that is programmed. The array keydef should contain the new string to be used (MAXFK long), and the length should be entered in flen.

The GETFKEY ioctl call works in a similar manner, except it returns the current setting of keynum.

The function keys are numbered like this:

 F1-F12    key 1 - 12 
 Shift F1-F12  key 13 - 24 
 Ctrl F1-F12  key 25 - 36 
 Ctrl+shift F1-F12 key 37 - 48 
 Home   key 49 
 Up arrow  key 50 
 Page Up   key 51 
 (keypad) -  key 52 
 Left arrow  key 53 
 (keypad) 5              key 54 
 Right arrow  key 55 
 (keypad) +  key 56 
 End   key 57 
 Down arrow  key 58 
 Page down  key 59 
 Insert    key 60 
 Delete   key 61 
 Left window  key 62 
 Right window  key 63 
 Menu   key 64

The kbdcontrol(1) utility also allows changing these values at runtime.


Søren Schmidt <sos@FreeBSD.org>
January 8, 1995 FreeBSD